PRICES include / exclude VAT
Homepage>CSN Standards>28 RAIL VEHICLES>2803 Calculations, directions for design>CSN EN 14363+A1 - Railway applications - Testing and Simulation for the acceptance of running characteristics of railway vehicles - Running Behaviour and stationary tests
Sponsored link
Not available online - contact us!
Released: 01.07.2019
CSN EN 14363+A1 - Railway applications - Testing and Simulation for the acceptance of running characteristics of railway vehicles - Running Behaviour and stationary tests

CSN EN 14363+A1

Railway applications - Testing and Simulation for the acceptance of running characteristics of railway vehicles - Running Behaviour and stationary tests

CURRENCY
197.78 USD
FREE Shipping
Number of Standard:CSN EN 14363+A1
Category:280307
Pages:200
Released:01.07.2019
Catalog number:507135
DESCRIPTION

CSN EN 14363+A1

CSN EN 14363+A1 This European Standard defines the process for assessment of the running characteristics of railway vehicles for the European network of standard gauge tracks (nominally 1 435 mm). In addition to the assessment of the running characteristics of vehicles for acceptance processes, this standard also defines quantities and dependencies that are not directly used for acceptance purposes. This information is for example intended for the validation of simulation models. It can also be used to define operating conditions outside the reference conditions to be used for the approval. The assessment of running characteristics applies to vehicles which: - are newly developed; - have had relevant design modifications; or - have changes in their operating conditions. The assessment process is based on specified target test conditions (see 3.1) given in this document. Experience over many years has demonstrated that vehicles complying with this standard can be operated safely on infrastructure with conditions more severe than the target test conditions, if the current general operating rules are applied. As an example it is generally current practice to restrict cant deficiency in curves below a certain radius. It may be necessary to adapt these operating rules, if a deterioration of the infrastructure conditions is observed. These operating rules are defined on a national basis. The procedure to evaluate these operating rules is out of the scope of this standard. NOTE 1: There are margins included in the specified limit values and the statistical evaluation. They cannot be quantified, but they explain why vehicles can also be operated at full speed and cant deficiency in many cases outside of the target test conditions. This standard also enables the demonstration of compliance against the target test conditions for the case that their combination is not achievable during tests. It is also possible to carry out the assessment of a vehicle for limited test conditions such as test zones 1 and 2 or reduced speed or reduced cant deficiency. In this case the approval of the vehicle shall be restricted accordingly. NOTE 2: National regulations sometimes allow the increase or decrease of the values for speed, curve radius and cant deficiency for local operation based on safety considerations taking into account the local characteristics of the infrastructure (track layout, track structure, track geometrical quality and contact conditions). These local characteristics can be different from those included in the assessment for the vehicle acceptance. NOTE 3: The methods of this standard can also be applied to gather information about the compatibility between the vehicle and infrastructure with conditions more severe than the target test conditions. The results of such investigations can be used to determine safe operating rules for such infrastructure conditions. Where testing the vehicle demonstrates that the performance of a vehicle complies with the requirements of this standard when operating at maximum speed and maximum cant deficiency under infrastructure conditions that are more severe than the target test conditions, the obtained results are accepted and there is no need to carry out additional tests to fulfil the requirements defined in this standard. This standard addresses four aspects: 1) Vehicles The assessment of the running characteristics applies principally to all railway vehicles. The document contains acceptance criteria for all types of vehicles with nominal static vertical wheelset forces up to 225 kN (of the highest loaded wheelset of the vehicle in the assessed load configuration specified in 5.3.2). In addition for freight vehicles with nominal static vertical wheelset forces up to 250 kN the acceptance criteria are defined. The acceptance criteria given in this document apply to vehicles designed to operate on standard gauge tracks. EN 14363:2016+A1:2018 (E) 10 2) Infrastructure In the acceptance process the range of curve radii is defined, for which the vehicle is assessed. A vehicle accepted according to the requirements of this standard is able to be operated on all standard gauge tracks complying with EN 13803-1 and EN 13803-2. EN 14363 also gives guidance about the handling of geometric track quality associated with the assessment. 3) Conditions of the wheel rail interface This standard contains requirements relating to the necessary range of equivalent conicity to be included in the assessment as target test conditions. In some national systems, either parts or all, equivalent conicities are significantly higher than the target test conditions of this standard. These cases are outside the scope of this standard. Nevertheless the methodology defined in this standard for the proof of running stability can also be used for higher equivalent conicities. NOTE 4: In these cases running safety is demonstrated by application of existing national requirements for high equivalent conicities during stability testing. Experience shows, that it is not necessary to include the maximum occurring values of equivalent conicity in such national requirements. 4) Operating conditions The document requires the specification of the combination of admissible speed and admissible cant deficiency as well as the loading conditions for each type of vehicle. NOTE 5: Recommended values of cant deficiencies for broad international approval are given in informative Annex H. This standard is not directly applicable to: - railways with different track layout, e.g. tramways, metros and underground railways; - railways with non-standard gauge tracks; but assessment can be conducted by analogy with this document, e.g. the test procedures described in this standard can be applied also to vehicles operated in networks with other track gauges (e.g. 1 524 mm and 1 668 mm). The related limit values and test conditions could be different. They are specified nationally taking into account track design and operating conditions. The strength of the vehicle and mounted parts, passengers and train crew vibration exposure, comfort, load security and effects of cross wind are out of the scope of this standard. This document includes the assessment of track loading quanti
Original English text of CSN EN Standard.
The price of the Standard included all amendments and correcturs.